How to Reset Epson Stylus 440

This procedure is to reset the Epson Stylus 440 printer when are the lights will blink and will not let you print.
Para realizar el reset lo que tiens que hacer es lo siguiente: To perform the reset tiens what to do is the following:

Hay que presionar y mantener apretado el boton de LOAD/EJECT (tomar hoja) y el de Cleaning (limpieza) . We must press and hold the button LOAD / EJECT (take up) and the Cleaning (cleaning).

Mientras mantienes apretados esos botones , tienes que presionar el boton de POWER (encendido) y tenerlo apretado hasta que las luces (ink out – tinta vacia y paper out- falta papel) empiezan a titilar o parpadear. While holding these buttons, you must press the power button (on) and keep it tight until the lights (ink out - empty ink and paper out-out of paper) start to flash or flicker.

Cuadno suceda esto suelta todos los botones. When it has to happen this release all buttons.

Cuando pasen 3 o 4 segundos apreta y mantenlo apretado el boton de CLEANING (limpieza) hasta que las luces que titilaban dejen de hacerlo. When you spend three or four seconds click and hold down the button CLEANING (cleaning) until the lights flickered stop.

YA ESTA!!! NOW THIS! ya quedo lista para usarla!! and am ready to use!

Seria conveniente que cada vez que se haga este procedimiento hacer una limpieza a la esponja interna de la impresora, por que alli deja depositado todo el exceso de tinta de la impresora y podria derramarse. It would be desirable that each time you do this procedure done to clean the sponge inside the printer, because there left on deposit all excess ink from the printer and may spill. Esto no es 100 % necesario pero seria muy bueno que lo hagas. This is not 100% necessary but it would be very good to do so.

How to reset the protection counter of Epson PX700W Resetter

   Epson PX700W Adjustment Program

FIX PRINTER ERROR "parts inside printer end service life, waste ink pad counter overflow error"

Please follow the steps below to reset the protection counter effectively.

1. Double click AdjProg.exe.
2. Click “Accept” button.
3. Click "Select" button. and select your printer model then click "OK"
4. Click “Particular adjustment mode” button.
5. Select on “Waste ink pad counter” and click “OK” button.
6. Click on “Initialization” button and the program will reset the protection counter.
7. Turn off the printer as a program instructed then turn on again.
8. Click “Finish” button. and its done!

Warning: You might end up with ink leaking out of the printer if you dont either replace the waste ink pad or install external waste bin.

Download

How to Read and Copy EEPROM Data from Epson Printers

How to Read and Copy EEPRsaya Data from Epson Printers

A. EEPRsaya data read

This function is to read all of EEPRsaya data and save read data to file. Procedure to read EEPRsaya data, Click the Read button to read all of EEPRsaya data.

B. EEPRsaya data copy (Backup EEPRsaya)

Before you replacing the main board, this function should be done to save all of necessary parameters from target (defective) main board by pressing “Backup” button. If the program detects all read parameters are correct, then you can replace the main board with new one. After that, you can restore all of read parameters onto replaced new main board by Restore button. If this function successes, some of later adjustments may be omitted such as heat protection.

Conditions : Before replacing the main board with new one.

How to Backup EEPRsaya data (Adjustment procedure)

• Click the backup button to backup the old main board data.

When the backup operation is succeeded,

• Replace the main board with new one.
• Turn on the printer and click the restore button.
• When the restore operation is succeeded, perform necessary adjustment.

When the backup operation is failed, Perform necessary adjustment.

How To fix Error number 0xc18a0301 on HP printers

Do the below steps on the front panel of the All-in-One printer:

A. - Press and Hold the “Print Photos” and “Red Eye Removal” buttons. Release both buttons. Display should say “Enter Special Key Combo”
B. - Press and release in sequence “Red Eye Removal”, “Print Photos”, “Red Eye Removal”
Display says "enter special key combo"
Press and release in sequence “Red Eye Removal”, “Print Photos”, “Red Eye Removal” .


If "support COxxFN0723BR" appears with "uiaux" message, perform the below steps:
2. Press and release the right arrow button until the display says “System Configuration Menu”. (on C8100 use Touch Screen)
3. Press and release the “OK” button.
4. Display should say “Hardware failure status”. If not there already, Arrow Key over to “Hardware failure status.
5. Press and release the “OK” button
6. Display should say “Hardware failure status: Clear. Press OK to clear”.
7. Press and release the “OK” Button. Message changes to “Hardware failure status Cleared. Press Cancel to continue”.
8. Press and release the “CANCEL” button as many times as necessary, so that, either the “Welcome to Photosmart Express” screen appears, or, the “Ink System Failure” screen appears. PLEASE DO NOT TRY TO PRINT AT THIS STAGE.
9. Using the Power Button, turn the unit OFF and unplug the power cable from back of the printer and wall outlet.
10. Wait 30 seconds for the power to get discharged and then plug the power cable into the wall outlet first and then into the back of the printer
11. Turn the unit on. The printer may display message “USE POWER BUTTON TO SHUTDOWN THE PRINTER” followed by “PRESS OK TO CONTINUE”. Press OK.
12. If the printer has already initialized, then go to the next step. If not, the printer will start the “ONE TIME INK INITIALIZATION PROCESS”. Allow this process to complete and do not interrupt. Once the initialization process is complete, the printer will print out a Diagnostic Page.
13. To verify printer functionality print a SELF TEST PAGE.

Brother MFC Printer Unable to Clean Error 46

This Reset Procedure is for Brother MFC Series Printer
Problem: Brother MFC Printer display "unable to clean" or Error 46
Solution:

• First turn of the printer
• Switch on the machine while holding down the “menu” button until all the leds are flashing on/off. Now you are in “maintenance” mode.
• Press 80
• Press the “mono start” button several times until you see “purge: xxxx”
• Press “2783” in order to reset the purge counter. You will see: “purge:0000”
• Press the "stop" button.
• Press “99” to exit the maintenance mode.

How to Reset Canon i255 and i320 Waste Ink Counter

Reset Methode for Canon Printers i255, i320

Step 1 : Manual for service mode

1. Unplug power and USB.
2. Open door and hold power button.
3. Connect power.
4. Close door, then release power button.
   

or try other step for manual service mode

1. Turn off the printer. And disconnect the printer cable.
2. Press and hold the POWER button, turn on the printer.
3. The indicator LED should be green.
4. Press and release the RESUME button , the indicator LED should be orange.
5. Press and release the RESUME button again, the indicator LED should be green.
6. Release both buttons.
   

Step 2 : Software for Permanent

1. Reconnect the printer cable.
2. Download and Run General Tools software resetter for Canon printers i320, i255 then
3. Select USB PORT
4. Choose SET DESTINATION 1 And it should be reset.
   

Remark “After service mode use software for permanent reset”

Introduction to HTML

Following is a brief introduction of HTML (Hyper Text Mark-up Language) used to create and maintain web pages. Though it must be emphasised, that many developers tend to use professional applications, namely, Dream-weaver 3, Flash 5, Fireworks 5 that make life much more simpler when creating and managing web sites. Web pages are written using HTML (hypertext Mark-up Language),

which consists of plain text, with certain formatting and control commands embedded using LESS THAN and GREATER THAN symbols. A page can include text, links to graphics files in .gif or .jpeg format, links to other sections of the page, links to other web pages (your own or other peoples) and links to other Internet resources, eg. e-mail. Therefore your text can be broken up with pictures and click-on links that take you automatically to other sections or pages, or load up the viewers email software, with your email address automatically inserted. Although HTML is an agreed standard, not all browser programs (Internet Explorer or Netscape) will behave in exactly the same way, when displaying your pages, so do expect some variation! For example, having bold and italic text is not included in the original standard. Some browsers will display the text as both bold and italic, whilst others will display one style and ignore the other. As new HTML standards appear, older browsers will not recognise all the enhanced features that are offered.get

How to Reset Printer Canon MP360 Waste Ink Tank Full

Reset procedure for Canon MP360 MultiPASS printer. The following procedure is copied from fixyourownprinter forum . Some user tried the procedure to reset waste ink tanf full on Canon MP 360 and reset error #343 Canon MP360 MultiPASS printer and mentioned it works.

Short Review For Canon MultiPASS MP360

The Canon MultiPASS MP360 Desktop Photo Printer Copier and Scanner delivers exceptional performance and versatility to the home office. Print high-quality text and photos quickly copy documents and graphics and easily scan photos and other images – all with one compact machine.

By using high-intensity color inks and pigment-based black ink the MultiPASS MP360 can increase your satisfaction with printing and copying output. It even delivers borderless copies and photos. borderless prints perfect for framing or the scrapbook. Both scanning and copying quality are improved with the use of CCD color scanning technology and a maximum software enhanced resolution of 9600 dpi with 48-bit color depth. Print speed the Canon MultiPASS MP360 up to 18 ppm in black up to 12 ppm in color

Manual Reset Procedure To reset waste ink tank error and reset error code #343

Manual Reset procedure Waste Ink Tank for Canon MP390 and Canon MP360 Just Follow this step how to reset waste ink tank full :

1. Start with printer on, press aadditional functions, Scan, Copy, Scan. Now you should be in service mode.
2. Select Test mode which is like the last available selection
3. Select #8 Printer Test, it will do something here like cleaning or something then it will come up with some other option this is where it gets a bit confusing cause now all it says is like 8-2 or 8-3 push the + or – button until it says 8-3 then hit the select button
   

• The menu will now say EEPROM Clear
• Select Ink count which is option (0) and press set
• Then press Stop/Reset Followed by the power button and then wait for it to restart.

How to Reset Canon iP1200 iP1600 and iP2200

Resetter Canon iP1200, iP1600, iP2200

1. Download software for Canon Pixma iP1200, iP1600, 2200 Printers from download link above.
2. Extrac downloaded file by extracded software like WinZip, 7Zip, Izarc, etc.but I recommend to use 7zip, because this software free and usefull and support many compresion format,
3. Goto extracted folder and then this tool by clicking GeneralTool.exe file
4. Select the connected USB port number from USB PORT where your printer installed.
5. Click LOCK RELEASE, and select the applicable model name printer in SET DESTINATION section. there are four choice there that is iP2200E, ip2200j, ip1600e, ip1200e . corresponding to your printer
6. To reset waste ink counter In CLEAR WASTE INK COUNTER section, select MAIN or PLATEN. The selected waste ink counter will be reset. MAIN resets the main waste ink counter, PLATEN resets the platen waste ink counter. If both the main and platen waste ink absorbers are replaced, reset both the main and platen waste ink counters.
   

DOWNLOAD Service Tool Software for Canon Pixma Printer iP1200, iP1600, iP2200

How to Reset Canon BJ F900 F890 F700 F500

Canon Printers BJ F900, F890, F700, F500 Reset Methode

1. Turn off the Canon Printers BJ F900, F890, F700, F500.
2. Press and hold the RESUME button, then press and hold the POWER button.
3. Release the RESUME button, then press and release the RESUME button two more times in succession. (youre still holding the POWER button during this). The printer mechanics will move momentarily. You are now in Service mode.
4. Pressing the RESUME key will select a function; for example, pressing RESUME 4 times will select the clear waste ink counter function. The lamp will alternate color with each key press.
   

• service/factory test printout, including ink sensor check
• EEPROM info printout
• EEPROM initialization
• Clear the waste-ink counter
• Printer model setting. (more selections beyond this- leave this alone)
• After selecting mode, press the POWER button to commit the change, and return to the top of the function selection menu. Pressing the POWER button again turns off the printer for a restart

How to Manual Reset Canon i6100

Reset Procedures Canon i6100

1. Turn off the printer
2. Press and hold RESUME button, then press and hold POWER button
3. Release the RESUME button
4. Next press and release the RESUME button two more times in succession, then release POWER button.
5. Press RESUME button for 4 times, this will select the clear waste ink counter function, The lamp will alternate color with each key press.

• Service/Factory test printout, including ink sensor check.
• EEPROM - Info printout.
• EEPROM – Initialization.
• Reset the Waste ink counter.
• Printer model setting. (More selections beyond this point – However it is best leave them unaltered – You have been warned!)

An introduction to Canon Error Codes

Like other brands, Canon copiers and printers are equipped with a mechanism to check the condition of the machine. It runs a check as needed, and will indicate an error in the control panel upon detention.

If an error is detected, the machine may be reset by turning it off and then on; however, this does not apply to E000, E001, E002, E003, E004, E005, E013, E020 or E717, preventing the user from casually resetting the machine when the fault is serious e.g., melting of the thermistor; otherwise, the fixing heater would overheat or toner would flow out of the hopper. If fault is identified as E000 through E003, the power switch will automatically go off in some models in 30 seconds if it is turned on. In the case of E004, power switch will go off in about 3 seconds. An authorized technician should reset E000, E002, E003, E004, E005, E013, E020 or E717. The table that follow indicate the nature and timing of detection of each error.

E000 to E399               Codes relating to the copier
E400 to E499               Codes relating to the feeder
E500 to E514               Codes relating to the finisher
E530 to E595               Codes relating to the finisher
E5F0 to E5f9               Codes relating to the saddle stitcher
E601 to E830               Codes relating to the copier

How to Reset Canon Pixma iP1200 iP1600 and iP2200

Canon Pixma iP1200, iP1600, iP2200 Resetter

1. Download software for Canon iP1200, iP1600, 2200 Printers.
2. Unzip downloaded file by WinZip, 7Zip, Izarc, etc
3. Run GeneralTool.exe
4. Select the connected USB port number from USB PORT
5. Click LOCK RELEASE, and select the applicable model name in SET DESTINATION
6. In CLEAR WASTE INK COUNTER, select MAIN or PLATEN. The selected waste ink counter will be reset. MAIN resets the main waste ink counter, PLATEN resets the platen waste ink counter.
   

If both the main and platen waste ink absorbers are replaced, reset both the main and platen waste ink counters.

Download Service Tool Software for Canon Pixma Printer iP1200, iP1600, iP2200

How to Reset Ink Level Cartridges PG 40 and CL 41 in Canon Pixma iP 1880

When refilling ink of cartridge PG-40 and CL-41 at Canon Printer Pixma iP 1880, ink level at cartridge do not become automatic full, but we have to do reset manual otherwise you change new PG-40 and CL-41 cartridges, you needn’t reset the cartridges.

There are some ways to reset of type Canon printers cartridge PG-40 and CL-41, one of the way to reset ink level cartridges PG-40 and CL-41, shall be as follows. Before you do reset you have to provide one of Canon Printers Cartridge PG-40 and CL-41 again.

Resetting level ink :

1. Tide of Cartridge Canon PG-40 and CL-41 (2nd) to Canon Printer Pixma iP1880 and let the cartridge detect untill finish. And try to test print.
2. After refill of cartidge canon PG-40 and CL-41 (1st), tide the cartidge PG-40 and CL-41 (1st) at printer and try test print again, usually the ink level status have full again. Otherwise succeed to try again.
   

Note :
Let easierly of first Canon Cartridges PG-40 and CL-41 i give the name (1st), and other Canon Cartidges PG-40 and CL-41 I give name (2nd).

How to Reset Canon Pixma MP110 and MP130

How to Reset Canon Pixma MP110 and MP130

Try this methode to reset Canon Pixma MP110 and MP130 printers

Resetting overflow error code for Printer Canon Pixma MP110 :

1. Turn on the printer.
2. Click Menu, and then Scan, Copy and Scan again. All – entered the service mode.
3. Select Counter
4. Click Copy – everything. Waste dropped to zero.
5. Turn off the printer POWER button.
   

Reset Canon Pixma MP130 Printer

1. Turn on the printer.
2. Press the MENU key, and then SCAN, COPY and SCAN again – entered the service mode.
3. Select NVRAM ACCESS further OK.
4. Select SET ABS-M LEVEL and set value equal to zero.
5. Select SET ABS-R LEVEL (if any) and is set to zero.
6. Turn off the printer POWER button.

Intruction To reset the HP 51645 or HP C6115

To reset the HP 51645 or HP C6115:

1. Refill your cartridge using your Mr. Ink Jet refill kit.
2. Following the diagram at right, place a piece of adhesive tape covering the HP 45 printhead, contacts, resetting the 51645aonly the four blue colored contacts (a contact is the individual copper square). Make sure that only those four are covered and no others.

3. Place cartridge in the printer. The printer may tell you that there is a problem with your cartridge. Ignore this message. The printer may print an alignment page. If so, allow it to do so.

4. Take the cartridge out of the printer. Remove the tape from the four blue contacts. Place the tape over the four red colored contacts. Make sure that only those four are covered and no others.

5. Follow step 3 again.

6. Take the cartridge out of the printer for the final time. Take the remaining tape off and place back in the printer. The printer should print out an alignment page and the estimated ink level in the toolbox should read full.

If Reset Method 1 did not work on your printer, go through the same procedure again, but this time using the green colored contacts in step 2 and the brown colored contacts in step 4. This method is more commonly used for the #15 or in the later officejet printers.


If neither of the reset methods above worked, you can cycle cartridges through to reset the level. You will need two extra cartridges and the one you refilled. First, put the refilled cartridge in the printer. Allow it to recognize the cartridge and print an alignment page. Take that cartridge out and place in the first extra cartridge. Allow it to recognize and print an alignment page. Take the first extra cartridge out and place the second extra cartridge in. Allow it to recognize and print an alignment page. Take the second extra cartridge out. Place the refilled cartridge back in the printer. It will print an alignment page and then the estimated ink level will be reset to full.

How to Reset Canon iP1880 IP 1100 iP1800 and iP2500 series

This tutorial solutions to reset canon iP 1880 or canon iP1800 series and work also in canon pixma iP1100, canon pixma iP2500. before reset using general tools you must reset the printer hardware. This way cannot to change ink level status canon pixma iP1880. following tutorial and software resetter to reset Canon Pixma iP1880.

Step 1: Reset hardware

1. Press Resume button hold for 1 – 2 minutes
2. Open the cover
3. Release the catridge and then put catridge again
4. Close The Cover
5. Turn Off
6. Then Turn On again
   

Step 2: Reset Software using general tools

• Download software resetter or general tools for canon pixma iP1880
• Driver should have been install correcly.
• Connect USB cable.
• Before connect power, press and hold power button then connect the power.
• At the same time Hold power button, and press reject button for 2 times then release power button.
• Run software resetter for canon iP1880.
• Don’t forget to open lock release in the software. ( note : to view locK release menu, min resolution 1024 x 728)
• Then select Set Destination to iP1880
• Check CLEANING and EEPROM CLEAR
• Click MAIN and PLATEN
• Finally test print by click TEST PATTERN1.
  

Note : for permanent reset waste ink canon iP1880 Printers pls, resetting use software resetter. Above way can be used at canon IP 1100, iP1800 and iP2500 series

Download service tool for Canon iP1880